Usually ready for shipment in 1-3 working days (depending on stocklevel).

Zinc die-cast cam buckle for indoor and outdoor use, suitable for 12 mm tension band.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Cam buckle for 20 mm Lashing.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Dualsafe – Cam buckle for 25 mm lashing.
Two springs for better clamping force / holding force.
Other color versions on request.

Our cam buckles from the series Dualsafe are a further development of a commercial clamp buckle.
We have extended this with another spring, the advantage: the clamping lever presses evenly on the webbing over the entire width. These clamp buckles offer you a very good price/performance ratio. Please ask for our pallet offers.
Other versions:
70AG025 – Cam buckle Dualsafe 25mm – 2,5kN (olive green)
70AS025 – Cam buckle Dualsafe 25mm – 2,5kN (black)

All our 25mm Cam buckles with a Breaking Strength of 2.5kN:

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Cam buckle Dualsafe for 25 mm Lashing.
Cathodic dip coating (KTL) – RAL9005 (black)

The cam buckle 70AS025 is based on the article 70AP025. The cathodic dip coating (KTL) in the color RAL9005 (black) gives the article not only a better appearance, but also a more resistant surface. Upon customer request, we offer other RAL colors.

All our 25mm Cam buckles with a Breaking Strength of 2.5kN:

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Double Cam buckle for 25 mm Lashing.

Load securing with a dual cam buckle: here, the loose ends of the webbing are each pulled past the clamping lever, tensioned by hand to an open end and fixed in place by the clamping levers installed in the dual cam buckle. In contrast to compression and tension ratchets, low pretensioning forces are achieved with a load securing system: dual cam buckle with lashing strap.

All our 25mm Cam buckles with a Breaking Strength of 2.5kN:

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Cam buckle for 25 mm Lashing.

Cam buckle made from high-quality galvanised die-cast zinc. Developed for high demands, this cam buckle is the ideal solution for a wide range of applications. Designed for a 25 mm wide webbing strap, it not only offers an optimum fit, but also a high level of safety.
The breaking strength of 450 daN makes our buckle reliable and robust in any situation. Whether you use it for professional equipment, outdoor activities or everyday use.

We also carry this zinc die-cast cam buckle as a stainless steel cam buckle in our program:

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Stainless steel Cam buckle for 25 mm Lashing.

We also have this stainless steel cam buckle in our program as a zinc die-cast cam buckle:

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Dualsafe – Cam buckle for 25 mm lashing, with two springs for better clamping force / holding force.
Other color versions on request.

Our Dualsafe cam buckles, Made by KONNEX are a further development of a cam buckle for 25 mm wide straps. We have improved the pressure point on the webbing by means of a second spring. The advantage is that the clamping lever presses evenly on the tension strap over the entire width.
This cam buckle lock offers you a very good price/performance ratio. Please ask for our pallet offers.
Other versions:
70AF050 – Cam buckle Dualsafe 25mm – 5,0kN (red)
70AS050 – Cam buckle Dualsafe 25mm – 5,0kN (black)
We will be pleased to submit you an offer for this also as a chrome-plated or nickel-plated version.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Cam buckle Dualsafe for 25 mm Lashing.
Cathodic dip coating (KTL) – RAL 9005 (black)

If a cam buckle in a special color is required, then you have come to the right place. We are happy to coat according to your wishes, such as the Dualsafe cam buckle shown here. We have provided this with a cathodic dip coating RAL9005 (cathodic dip coating, black). This surface protection not only gives the article a better appearance, but also a more resistant surface. On customer request even with your company logo.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Cam buckle for 25 mm Lashing.

Cam buckle body: Galvanized steel
Cam buckle handle: Zinc die-casting

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Cam buckle for 35 mm Lashing.

A clamp buckle, often referred to as a tension belt clamp buckle, is a metal housing with a lever mechanism. The lever has a serrated edge that clamps the strap when it is pressed down. The strap is fed through an opening. When the strap is tightened, the lever is pressed down, causing the serrated edge to hold the strap in place. To release the strap, the lever is pressed, causing the serrated edge to release the strap. The buckle is usually made of robust metal, sometimes with plastic components, and the strap is often made of durable fabric.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Cam buckle for 50 mm Lashing belt.

A cam buckle for heavy loads – the lever made of die-cast zinc and the housing made of high-strength steel.
Lashing possibilities with a 50 mm wide webbing strap possible. On request, we coat this cam buckle 70CQ100 in various RAL colors.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Cam buckle for 50 mm Lashing belt.
Powder coated – RAL 9005 (black)

A special needs clamp lock has several features and characteristics that distinguish it from conventional clamp locks. Here are some factors and considerations that could be taken into account when selecting or designing such a clamp lock:
Material and durability: the lock should be made of high quality and durable material to withstand the special requirements.
Load capacity: the clamp lock should be able to withstand heavy loads and vibrations, depending on the requirements of the application. This could be relevant for applications in heavy industry, mining or transportation.
Temperature resistance: If the clamp lock is exposed to extreme temperatures, it should be able to withstand these conditions without compromising its function or strength.
Security: Depending on the application, additional security features might be required, such as a secure locking mechanism.
Weather resistance: If the clamp lock is used outdoors, it should be weatherproof and able to withstand the effects of rain, snow and UV radiation.
Adaptability: a special needs clamp lock should potentially be adaptable to different mounting points or configurations to meet specific needs.
Approvals and certifications: Depending on the application, special approvals or certifications could be required to ensure the lock meets applicable standards.
The specific requirements for a clamp lock will depend on the application. It is important to clarify these requirements in advance and, if necessary, work with a professional or a company that specializes in the design and manufacture of specialized locks for specific applications.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

With a length of 53 mm, this stainless steel pointed hook / double finger hook is designed for use that requires special requirements.

In conjunction with a stainless steel pressure ratchet is a perfect combination. A 25 mm wide tension band is used.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook for 25 mm Lashing.
Length: 47 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook for 25 mm.
Length: 50 mm

A profile hook is a practical companion in the field of load securing, it is quickly used and is designed for bandwidth of 25 mm.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook for 35 mm Lashing.
Length: 62 mm

A j-hook or profile hook, is ideal for securing loads on a truck and van.
This profile hook is suitable for 35 mm lashing straps.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook for 35 mm Lashing.
Length: 74 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook for 35 mm Lashing.
Length: 86 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook for 35 mm Lashing, with Safety latch.
Length: 87 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Finger hook for 35 mm Lashing.
Length: 90 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook short, for 50 mm Lashing belt.
Length: 74 mm

*** Very high corrosion protection due to our KOsil – passivation ***

A swivel hook or profile hook, double finger hook is ideal for securing loads in trucks and vans.
This standard swivel hook 72CQ300 is suitable for 50 mm tension webbing.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook short, for 50 mm Lashing belt. Length: 74 mm

A j-hook is used in load securing to ensure a stable and secure connection between the load and the transportation surface (e.g. a truck or trailer floor). The main function of the pointed hook is to enable a fastening or lashing system by connecting it to lashing straps.
How it works:
1. fastening the lashing straps or chains: The pointed hook is attached to a stable point on the loading surface or to the load itself. It is generally used to connect lashing straps or chains to the corresponding ratchets.
2. lashing the load: By using lashing straps connected to the pointed hook, the load can be fixed and held in position. The hook itself helps to control the tension of the straps and ensure that the load does not slip during transportation.
3. preventing movement: The pointed hook helps to secure the load against lateral movement, vibrations and shocks during transportation, which is particularly important with long or heavier loads.
Advantages:
– Effective securing: the pointed hook ensures a robust connection and reduces the risk of the load slipping or coming loose during transportation.
– Simplicity and flexibility: The hook is easy to handle and can be attached to different points on the loading area as required.
– Versatility: Pointed hooks are available in various

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook – for 50 mm Lashing belt.
Length: 85 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook for 50 mm Lashing belt, with Safety latch.
Length: 96 mm

A profile hook with a spring-loaded sheet metal trap, the use is with a 50 mm wide webbing.
The sheet metal trap ensures that the profile hook does not jump out of the lashing.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook for 50 mm Lashing belt. Length: 107 mm

J-Hook is also called a double finger hook, it can be used in many ways and is very suitable for securing loads on a truck trailer or in the van.
Our hooks are made of high quality steel and galvanized CrVI-free.
In combination with a pressure ratchet or an ERGO ratchet, these are the perfect unit to ensure safety in transportation.

More hooks for webbing dimensions from 25 mm up to 75 mm can be found in our OnlineShop.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook for 50 mm Lashing belt, with Safety latch.
Length: 110 mm

This profile hook / pointed hook – long version is equipped with a spring-loaded sheet metal latch that prevents it from jumping out. It is used with a 50 mm wide webbing strap.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Finger hook for 50 mm Lashing belt. Length: 133 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Finger hook for 50 mm Lashing belt, with tube. Length: 158 mm

Single-finger profile hook for direct connection to a push or pull ratchet – as a fixed end.
Steel tube welded on

Usually ready for shipment in 1-3 working days (depending on stocklevel).

J-Hook / Double finger hook for 75 mm Lashing belt.

J-Hook are also called profile hooks and are used to attach lashing straps to lashing points or to external frame hole profiles of the vehicle.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Claw hook for 35 mm Lashing belt, open version.

Our claw hooks include a strap width of 35 mm and is used in conjunction with a pressure ratchet when securing loads.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Claw hook for 50 mm Lashing belt, open version.

Another aid in load securing is the claw hook, this end fitting is used with a two-piece lashing strap.
We have these for the following strap widths for you in the offer: 25 mm, 35 mm, 50 mm and 75 mm.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Flat hook / Pallet hook for 25 mm Lashing, with Safety device.

Flat hook with spring-loaded safety pin, this prevents loosening from a lashing rail, this is used with a width of 25 mm.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Flat hook for 25 mm Lashing, without Safety device.

A flat hook for bar lashing rails is an end fitting that is used for load securing.
Rod lashing rails are rails or rail systems that are installed in vehicles such as vans and trailers.
They are used to secure transported goods during transportation.

It is used to securely fasten tension belts to the rail.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Flat hook / Pallet hook for 50 mm Lashing belt.

Flat hook made of high-strength steel for load securing for 50 mm webbing.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Flat hook / Pallet hook for 50 mm Lashing belt.
Length: 115 mm

A flat hook or heavy profile hook has been developed for securing loads in lorries and vans.
Forged version, designed for lashing strap widths of 50 mm.

A “flat hook” in load securing could be used in various ways, depending on the type of load, the means of transport and the specific requirements. Here are some possible applications:
Connection with lashing straps: flat hooks serve as end fittings for lashing straps. These straps are placed around the load and then secured by the flat hook to hold the load in place.
Special applications: Depending on the specific requirements of the load and the transport, flat hooks may also have been developed for special applications, e.g. for transporting construction site materials or other heavy goods.
Anchor point for nets: In some cases, flat hooks are used to attach safety nets or covers over the load. These nets are used to prevent loose parts of the load from falling during transport.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Forged and galvanized triangle snap hook / load hook for 25 mm tension band.
Design: with sheet metal latch

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Forged and galvanized triangle snap hook / load hook for 25 mm tension band.
Design: with wire latch.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Load hook for 25 mm Lashing, with Safety latch.

A simple and uncomplicated form of load securing in a van is the use of a load securing net.
This is placed over the load to be secured and hooked into e.g. lashing recesses, D-ring or U-bolts by means of the snap hook sewn to the lashing strap.

The load hooks have a safety device against loosening, which is designed in the form of a sheet metal trap or a wire trap.

72AQ018 Load hook 25 mm – 25 kN (with latch)
72AQ019 Load hook 25 mm – 25 kN (with spring)

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Load hook for 25 mm Lashing, with Safety spring.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Snap hook / Flat hook for 35 mm Lashing, twisted, with Safety latch.
Length: 130 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Snap hook / Flat hook for 50 mm Lashing belt, with Safety latch.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Snap hook / Flat hook for 50 mm Lashing belt, with Safety latch, twisted.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Triangle load hook for 50 mm Lashing straps, with Safety latch.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Triangle load hook for 75 mm Lashing belt, with Safety latch.
Opening: 30 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Swivel Hook for 35 mm Ratchet, without bolt.
VDI 2700 Part 8.1 conform
Length: 100 mm

This swivel hook is mounted as a fixed end on a pressure ratchet.
A swivel hook is a special form of hook that is used in various applications, including load securing. The name “swivel hook” is derived from the hook’s ability to rotate or swivel on its own axis. This mechanism enables more flexible adjustment and facilitates handling in various situations.

In load securing, the swivel hook is often attached to one end of a lashing strap or lashing chain. The swivelling head of the hook offers more flexibility when attaching to different anchor points or fixing points. This can be particularly useful when the direction of the pulling angle can vary.

The advantages of a swivel hook in load securing can be

Flexibility: the swivelling head of the hook allows better adaptation to different angles and surfaces.

Reduction of twisting: The ability of the swivel hook to rotate on its own axis minimises the risk of twisting of the tensioning strap or lashing chain, which contributes to safer load securing.

Easier handling: The movable head makes it easier to attach the hook to different anchoring points, which makes the entire load securing process more efficient.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Swivel Hook for 35 mm Lashing straps, with nut and bolt.
VDI 2700 Part 8.1 conform
Length: 117 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Swivel Hook for 50 mm Ratchet, without bolt. Length: 105 mm

A swivel hook is a hook that can rotate on its own axis. This rotating function prevents connected ropes, chains or belts from twisting or tangling, which is particularly important when securing loads.
1. avoidance of twisting – The ability to rotate allows the load to move to a certain extent without the lashing equipment (e.g. tension belts or chains) twisting or becoming excessively stressed.
2. even force distribution – A swivel hook ensures that the tensile forces are optimally distributed, which increases the stability of the load.
3. increased safety – less twisting means less tension on the lashing equipment, reducing the risk of material fatigue or failure.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Swivel Hook with sleeve for 50 mm Ratchet, with nut and bolt.
Length: 106 mm

Usually ready for shipment in 1-3 working days (depending on stocklevel).

S-hook, black, PVC coated.
In conjunction with a 25 mm ratchet, it is a simple way of securing a load.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Triangle / Delta Bracket for 25 mm lashing strap.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Triangle for 35 mm lashing strap.

An isosceles butt welded triangle for 35 mm webbing.
One of our end fittings that are used for securing loads.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Triangle for 50 mm webbing.

A closed, isosceles triangle for 50 mm webbing.
End fitting for cargo securing.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Belt shackle, to be used as an end fitting for a load securing system with a strap width of 75 mm and an LC of 6,000 daN.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Belt shackle, to be used as an end fitting for a load securing system with a strap width of 75 mm and an LC of 10,000 daN.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Our smallest pressure ratchet for a 25mm wide webbing, universally applicable for lighter loads.

With an LC of 400 daN in straight pull, this Hobby ratchet is one of the smallest in our range. With a strap width of 25 mm, different loads can be secured. The 71AQ008 is a pressure ratchet without lever safety device, the tensioning movement during load securing always goes in the direction of the loose end.

All our 25 mm Pressure Ratchets with a Breaking Strength of 8 kN:

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet for 25 mm webbing, without Lever lock.
RAL9005 (black)

This black (black/silver) Hobby ratchet with an LC of 400 daN in straight pull is one of the smallest in our range. This is used with a 25 mm wide webbing.

All our 25mm Pressure Ratchets with a Breaking Strength of 8kN:

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet / Hobby ratchet for 25 mm Lashing straps.

With an LC of 400 daN in straight pull, this stainless steel Hobby ratchet is one of the smallest in our range. With a strap width of 25 mm, different loads can be secured.

All our 25mm Pressure Ratchets with a Breaking Strength of 8kN:

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet for 25 mm Lashing.
Handgrip: steel, wide version

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet for 25 mm Lashing.
Handgrip: wide, Inox

Load securing with ease and precision!
Our article number 71AX015 is a first-class 25 mm stainless steel (inox) pressure ratchet – your reliable solution for safe transport.
With a breaking load of 15 kN, this small but powerful ratchet offers maximum safety.

The wide handle ensures comfortable handling, while the stainless steel construction stands for robustness and durability.
This pressure ratchet is ideal for securing loads firmly and reliably, whether for commercial transport or private use.

You can rely on the highest quality and efficiency.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet for 35 mm Lashing.
Handgrip: wide, Inox

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet for 35 mm Lashing.
Handgrip: wide, steel

A pressure ratchet is a tensioning tool used to securely fasten goods for transport.
It consists of a fixed end (webbing with end fitting) and a loose end (webbing with end fitting) at the other end.
The webbing is placed around the load and then tightened with the pressure ratchet to secure the load.
There are different sizes of pressure ratchets that are used for different applications.
It is important that the ratchet is used correctly to ensure that the load can be transported safely.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet with Lever lock for 35 mm webbing.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet with Lever lock for 35 mm webbing.
Handgrip: narrow, steel

Our 35mm pressure ratchet is often used to secure loads in a van, car or on a car trailer.
It is equipped with a user-friendly plastic handle and a lever lock

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet with Lever lock for 35 mm webbing.
RAL9005 (black)
Handgrip: wide, plastic

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet with lever safety catch for 35 mm tensioning strap with an STF value of 330 daN.
Special car lashing

Matching swivel hook 35mm – 30kN (72BQ009)

Discover our latest 35 mm pressure ratchet.
Developed to revolutionise the securing of cars on vans! Our 35 mm pressure ratchet is based on a thorough development and offers safety for the transport of vehicles.
With a secured STF value of 330 daN, our pressure ratchet is designed to ensure maximum safety even under extreme conditions. The ratchet has been tested in accordance with the specifications of DIN EN 12195-2 – for absolute reliability and quality. Rely on our pressure ratchet to securely and safely fasten your cars to the transporter. It is a reliable solution for a trouble-free and safe transport experience.
Your safety is our top priority!
Move with the future of car securing – with our 71BQ033 pressure ratchet!

VDI Guideline 2700 Sheet 1 – “Load securing on road vehicles”
This guideline provides guidelines and recommendations for the safe securing of loads during transport on road vehicles. Here are some key aspects that can be covered in the guideline:
Objective: the aim of the guideline is to ensure road safety by providing guidance on the correct securing of loads on vehicles. This is important to prevent accidents that could be caused by unsecured or improperly secured loads.
Responsibilities: The guideline could encourage the various parties in the transport process (such as the shipper, carrier, driver, etc.) to take on certain responsibilities in relation to load securing.
Calculation of securing forces: Methods and formulas can be provided to calculate the required securing forces for the different types of cargo and means of transport.
Securing equipment: The guideline could provide recommendations for suitable securing equipment such as lashing straps, anti-slip mats or other aids to effectively secure the load.
Testing and documentation: Instructions may be included for carrying out load securing tests before and during transport and for documenting the securing measures carried out.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet with Lever lock, for 35 mm webbing.
Handgrip: wide, Inox

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet with Lever lock for 35 mm webbing.
Handgrip: plastic, narrow version
Swivel J-Hook: mounted

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet for 50 mm Lashing belt.
Handgrip: wide, steel

Short pressure ratchet, with a length of 134 mm it is one of the smallest in our delivery program in the range of 50 mm webbing.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Stainless steel pressure ratchet in a short version for 50 mm lashing straps.
Ratchet handle: stainless steel, wide version

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet with Lever lock for 50 mm webbing.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

The one with the red handle – our standard pressure ratchet with lever lock for 50 mm lashing strap.
Handle design: plastic, red
Lever length: 188 mm

Our standard pressure ratchet 71CQ050 is used on a truck or van. In connection with belt strap and end fittings, it secures your load against slipping and holds it in the intended place on the loading area.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

SELF-LOCK
With a roll up system your load is quickly secured. No cumbersome insertion of the webbing into the winding shaft, no free-hanging webbing after securing the load. Particularly easy to use. Due to the automatic retractor, the webbing is slightly under tension during the securing process. If the webbing is rewound too quickly, e.g. if the end fittings are released, the system is blocked by the safety rewind lock in the rewind spool by means of a locking lever, thus preventing injuries caused by whirling end fittings, and the webbing is rewound in a controlled manner.

• the safest and smartest retractable ratchet harness in the world
• the most automatic retractable harness in the world, certified by TÜV / GS
• fast, easy and safe to use
• built-in spring automatically retracts the webbing for easy storage
• built-in self-locking mechanism to control the retraction speed
• safety retraction lock when the retraction speed is too fast, the best protection for the user
• strong and abrasion-resistant polyester webbing

Usually ready for shipment in 1-3 working days (depending on stocklevel).

NEW – the one with the red handle, our pressure ratchet for 50 mm lashing strap.
Special feature: higher STF value than the standard pressure ratchet.
Handle design: plastic, red
Lever length: 213 mm

With the red handle – Our new pressure ratchet 71CQ059 with higher STF value = 350daN.
Used on a truck or van. In conjunction with webbing and end fittings, it secures your load against slipping and holds it in the intended place on the loading area.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

ABS-Pressure ratchet with Lever lock for 50 mm webbing.
RAL9005 (black)
ABS function – Active Brake System, allows controlled release of preload force.

Why ABS for a pressure ratchet?
Safety comes first. When transporting goods, your secured load can still ‘settle’ or move a little. This is why the load can suddenly start to move uncontrollably when released with a normal pressure or long lever ratchet and possibly cause an accident.
This situation can be prevented with an ABS pressure ratchet (Active Brake System).
An ABS ratchet allows you to release the tension in small steps so that you can react better to a potential problem.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Long lever-Pressure ratchet with Lever lock for 50 mm webbing.
Toothing: double

In cargo securing, a long lever ratchet refers to a special tool used to tighten cargo on transport vehicles such as trucks, trailers or ships. This tool is used to tighten tension belts or lashing straps with high tension in order to securely fix and secure the cargo during transportation.

A long lever ratchet in cargo securing has a long lever arm that allows the operator to apply a significant tensioning force to the straps. It usually consists of a handle, a long lever and a mechanism that generates the tensioning force. The operator applies the ratchet to the lashing strap and uses the lever to tighten the straps. This allows the load to be securely held in place to prevent slipping or tipping over during transport.

Long lever pressure ratchets are particularly useful when transporting heavy loads or delicate goods where secure fixation and tensioning of the belts is critical. They are often used in the logistics and transport industry to ensure the safety of the load during transport and prevent accidents or damage.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet with Lever lock for 50 mm webbing.
RAL9005 (black)

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet with Lever lock for 50 mm webbing.
Handgrip: narrow, plastic

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pull ratchet ERGO with Lever lock for 50 mm webbing. Handle length: 260 mm Handgrip: wide, plastic (red)

With the red handle.
Our standard ERGO pull ratchet 71CQ060 finds its use on a truck or van. In combination with webbing and end fittings, it secures your load against slipping and keeps it in the intended place on the loading area. With a lever length of 260 mm, the operation of the long lever ratchet is easier in contrast to a pressure ratchet and a much higher pretensioning force / STF value is achieved.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pull ratchet ERGO with Lever lock for 50 mm webbing. Handle length: 260 mm Handgrip: wide, plastic (black)

Long-lever ratchets, also known as ERGO pull ratchets, are ideal for the safe transportation of heavy goods, as they enable high pre-tensioning forces with little effort. They are used in logistics, construction and industry, among others. Simple and ergonomic handling when securing loads are the advantages of these lashing straps.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Long lever Pull ratchet ERGO with Lever lock for 50 mm webbing.
Handle length: 300 mm
Handgrip: PE, red

One of the common clamping elements for heavy goods is a pull ratchet, this is also called ERGO ratchet. In contrast to a push ratchet / short lever ratchet, this is more ergonomic for the user. When lashing and tensioning, the lever, as the name of the ratchet already says, is pulled (down) and not pressed, this protects the spine of the user. Another advantage is that higher pretensioning forces – STF (Standard Tension Force) can be achieved here when securing the load.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

ABS-ERGO Pull ratchet with Lever lock for 50 mm webbing.
RAL9005 (black)
Handgrip: wide, plastic
ABS function – Active Brake System, allows controlled release of preload force.

Why ABS? It’s as simple as it is obvious.
It’s about your safety, because when transporting goods, your secured load can still ‘settle’ or move a little. This is why the load can suddenly start to move uncontrollably when released with a normal pressure or ERGO long lever ratchet and possibly cause an accident.
This situation can be prevented with an ABS (Active Brake System) towing ratchet.
An ERGO ABS long-lever ratchet allows you to release the tension in small steps so that you can react better to a potential problem.
Our ABS-EGRO ratchets are tested in accordance with DIN EN 12195-2 for the prescribed lashing capacity (LC) and breaking load (BL).

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Geared pull ratchet with Lever lock for 50 mm webbing.
Handgrip: wide, Plastic

50 mm pull ratchet with built-in gearbox for high preload forces. Depending on the lashing belt, STF values of 800 daN can be achieved with ease.

The decisive factor for good load securing is the pretensioning force to be achieved, depending on the application, very high STF values are required for load securing, our ERGO long lever ratchet is equipped with a gearbox.
Due to the gear ratio, you can achieve much higher STF values with this ERGO gear ratchet than with a usual ERGO long lever pull ratchet at the pre-tensioning force. Our ERGO gear ratchet (71CQ064) has a lever lock and is designed for 50 mm lashing straps.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet with Lever lock for 50 mm webbing.
Swivel Hook: mounted
Handgrip: Aluminium

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet set with lever safety device for 50 mm lashing strap
Swivel hook: mounted

Set:

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Pressure ratchet set with Lever lock for 50 mm webbing.
J-Hook / Finger hook: mounted

Set:

Usually ready for shipment in 1-3 working days (depending on stocklevel).

ABS-Pressure ratchet set with Lever lock for 50 mm webbing.
J-Hook / Finger hook: mounted

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Heavy Duty Pressure ratchet without Lever lock for 75 mm webbing.

Heavy-duty pressure ratchets are not suitable for tie-down lashing, they are used exclusively for direct lashing and the STF value is not shown on the lashing strap label.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

75mm gear pull ratchet with built-in gear for high pretensioning forces. Depending on the lashing strap, STF values of 500 daN are easily achieved.
Handle design: wide, plastic

The decisive factor for good load securing is the pretensioning force to be achieved, depending on the application, very high STF values are required for load securing, our ERGO long lever pull ratchet is equipped with a gear.
Due to the gear ratio, you can achieve much higher STF values with this ERGO gear ratchet than with a usual ERGO long lever pull ratchet at the pre-tensioning force. Our ERGO gear ratchet (71DQ064) has a lever lock and is designed for 75 mm lashing straps.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Heavy duty pressure ratchet for 100 mm lashing straps – steel version

A heavy-duty pressure ratchet is a tool used to secure and tension heavy loads. It consists of a ratchet mechanism, which is driven by a lever, and a stop shoe, which is pressed against the load. It allows loads to be secured and tensioned with great force.
The process of using a heavy-duty compression ratchet is as follows:
1. position the heavy-duty pressure ratchet at the desired location.
2. operate the lever to actuate the ratchet mechanism and secure the load.
3. when the desired tensioning force is reached, close the lever and the load will remain securely held.
4. to release the tension, open the lever to release the ratchet mechanism.
It is important to note that the maximum tensioning force that can be applied to the heavy-duty ratchet depends on the type and size of the heavy-duty ratchet. It is therefore important to follow the manufacturer’s instructions and ensure that it is suitable for the intended application.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Buckle for 25 mm Lashing.
Cathodic dip coating – black

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Double buckle bended, for 25 mm Lashing belt, without hook.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Airline fitting / Single stud fitting, with Inox Ring.

Airline fitting with a stainless steel ring for airline rail/lashing rails.

Load securing in a box van
Airline fitting with a stainless steel ring as a connection between lashing straps and airline rails / airline guide rails.

– Compatible with all single airline guide rails
– Safe and quick installation
– High quality materials
– one-handed operation

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Airline fitting / Double stud fitting.
End terminal without Ring
Breaking strength (BS): 2.000 daN
Stamp: ISO 9788

Airline fitting for airline rail/lashing rails.

An airline fitting is attached to an airline rail that is fitted along the side walls or floor of the vehicle.
Straps can be hooked onto it to secure the load for transportation.
The airline fittings are tested in accordance with ISO 9788. They are flexible and provide security when securing the load and are therefore an important part of load securing in transportation.

Also available as an airline fitting with ring.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Clamping buckle / Sliding buckle for 50 mm Lashing belt.

Clamping buckle / Sliding buckle adjustable.
Range of use 50 mm webbing

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Simple lashing to combination lashing rails is made possible by the anchor rail fitting for 50 mm lashing straps.
Our lashing rail fittings have a breaking load of 2,000 daN.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Hook for 50 mm Webbing.
Endfitting with Hook for KRONE Trailers and Profi Liner.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Double buckle for 50 mm Lashing belt.

A double buckle is required for cargo securing where lash straps are used.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Clamp Bar / Clamping board with extendable aluminium plates.
Adjustable Length: 2.40 – 2.70 m
Breaking Load (BL): 420 daN

Cargo Plank / Clamp bar are placed on the dropside and secure the load against slipping and tipping.
The intermediate wall fasteners are made of aluminum, the tensioning on the dropside is done by means of rubberized levers.

With a clamping board you have an additional tool to fix the load.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Canvas runner trapezium with 2 white B30S roles (with bearing).
Side tarpaulin roller

Our tarpaulin rollers:

• Very good rolling properties
• Versions for different systems available
• KONNEX quality

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Canvas runner / roller with 2 white roles (with Bearing) Dekra-Certifikate

Certificate regarding the strenght testing of aids for load securing according to the DEKRA requirements profile VA 80-13-TTD-50 for sliding curtains and DIN EN 12641-2 minimum requirement sliding curtains.

Usually ready for shipment in 1-3 working days (depending on stocklevel).

Blocking unit with security grub screw
Aluminium unit: 16 mm x Ø12 mm
VA screw: M6 x 16 mm

For tarpaulins and awnings, the kedder/blocking unit is held in the correct position.
Fastening by means of SW 3.